Two stroke single blade trimmer

NegotiableUpdate on 01/20

Model

Nature of the Manufacturer: Producers

Product Category

Place of Origin

Online Consult

Overview

The two-stroke single blade trimmer is mainly used for fence trimming, tea tree pruning and pruning to promote the growth of new tea buds. This model SY-HT600A is an economical model with affordable price, stable performance, and low failure rate.

Product Details

　　Two stroke single blade trimmeroperation

1. Check that the handle switch is in the "ON" position;

2. When starting in a colder environment, turn the choke handle to the "OFF" position, which is the upper end. If the ambient temperature is high or in a hot state, turn the choke handle to the "ON" position (the position during normal use); 3. Pump oil to the carburetor until fuel can be seen flowing out of the return pipe;

4. Gently pull the starter until it is in contact with the start dial, then pull hard to start the gasoline engine. Rough pulling of the starter is not allowed, as discontinuous pulling can cause discontinuous ignition of the spark plug and prevent the machine from starting.

　　Precautions before use

1. Before use, please read the user manual carefully to understand the performance and precautions of the machine.

The purpose of the hedge trimmer is to trim hedges and shrubs. To avoid accidents, do not use it for other purposes.

3. The hedge trimmer is equipped with a high-speed reciprocating cutting blade, which can be very dangerous if operated incorrectly. So, when tired or uncomfortable, after taking cold medicine or drinking alcohol, do not use a hedge trimmer.

The gas emitted by the engine contains carbon monoxide, which is harmful to the human body. Therefore, do not use hedge trimmers indoors, in greenhouses, or in tunnels where ventilation is poor.

5. Do not use in the following situations.

① When the feet are slippery and it is difficult to maintain a stable working posture.

② When it is difficult to confirm the safety around the work site due to thick fog or nighttime.

③ When the weather is bad (rain, strong winds, thunder, etc.).

6. When using the hedge trimmer for the first time, it is necessary to seek guidance from an experienced person on its usage before starting actual operation.

7. Excessive fatigue can reduce attention and become a cause of accidents. Do not make the work plan too tight. The continuous work time should not exceed 30 to 40 minutes each time, and there should be 10 to 20 minutes of rest time. The daily work time should be limited to no more than two hours.

8. Minors are not allowed to use hedge trimmers.

　　Two stroke single blade trimmerMaintenance and upkeep:

1. Before, during, and after use, all components of the equipment should be carefully inspected. If any mechanical damage or loose or detached fasteners are found, they should be replaced and adjusted in a timely manner. It is not allowed to operate machinery with defects or missing parts.

2. The blade should be lubricated with engine oil every 1-2 hours of operation. Add ZFG-2 composite calcium based grease to the gearbox every 20-30 hours of use.

3. The pruning diameter of the trimmer should not exceed 10 millimeters. If you cut thick branches or foreign objects during homework and feel abnormal noise or vibration from the machinery, you should quickly shut down and remove the foreign objects.

4. Clean the air filter sponge with detergent or laundry detergent every 50 hours of work, squeeze it dry, and dry it in the sun. Clean the carbon buildup on the spark plug after every 150 hours of work; Replace the fuel filter every 3 months of work;

5. After daily use, clean the machine body, rinse the tea juice on the blade with clean water, dry it, and then inject engine oil into the oil injection hole.

6. Long term parking of machinery should remove dust and debris from the surface of the machine. Release fuel from the fuel tank. Remove the spark plug, remove the carbon deposits, inject a few drops of clean engine oil into the cylinder, gently pull the starter a few times to lubricate the cylinder wall with the oil. Install spark plugs, package and store in a dry place.