Domestic 60 type small salt spray test chamber

60 type small salt spray environment corrosion testing equipment

Model specifications:

• Y-250CStudio size: D600 * W900 * H500mm

• Y-750CStudio size: D750 * W1100 * H500mm

• Y-010CStudio size: D850 * W1300 * H600mm

• Y-016CStudio size: D850 * W1600 * H600mm

• Y-020CStudio size: D900 * W2000 * H600mm

Reference standard:

GB/T10125-2012, GB/T2423.17, GB/T5170.8, GB/T10587 and other standard requirements;

Technical indicators:

• Temperature range of experimental chamber: RT+10 ℃~65 ℃

• Saturation bucket temperature range: RT+10 ℃~70 ℃

• Humidity range:>95% RH

• Temperature fluctuation: ≤± 0.5 ℃

• Temperature uniformity: ≤ 2 ℃

• Temperature deviation: ≤± 2 ℃

• Salt spray settling amount: 1-2mL/80cm2 · h (average value over 16 hours)

• Spray mode: pneumatic, continuous, intermittent, programmable and other spray modes

• Test methods: Neutral Salt Spray Test (NSS Test), Acetic Acid Salt Spray Test (AASS Test), Copper Accelerated Acetic Acid Salt Spray Test (CASS Test)

Introduction to Structural Design:

60 type small salt spray environment corrosion testing equipmentBeautiful appearance design, reasonable structure, smooth and natural lines. Both the inner and outer shells are made of flame-retardant high-quality PP plastic sheets, with a durable temperature of over 85 ℃. The joints between the sheets are milled and flattened to form a 90 degree right angle, and then melted with a high-temperature welding gun using plastic welding wire. After cooling, the welds are firm, and the joints of the entire box are flat, the box structure is compact, and the appearance is bright. Various auxiliary accessories and facilities are also made of corrosion-resistant materials.

The material of the box cover is flame-retardant high-quality PP board, and the front and rear observation windows can observe the condition of the indoor specimens from the outside without affecting the test results. And the box cover is designed with a good top angle of 110 degrees, so that the condensed water generated during the test process will not drip onto the sample and affect the test results. The box cover and body are sealed with water to prevent salt spray from overflowing, which may affect the test results and corrode other equipment in the room, and may even cause harm to the test operators.

The cover of large box (010 and above) is automatically opened by cylinder (Taiwan, China Yadeke), which is convenient. The opening angle is about 80 degrees, and the air source is compressed air with a pressure of 0.4 megapascals. (750 model uses gas spring assisted opening)

Water tank (saltwater, pure water): adopts a hidden structure with a drainage valve, easy to clean.

Saturation bucket: made of SUS304 high-grade stainless steel pipe welding, with good high temperature and high pressure resistance performance. Using the Henry's law, heating and humidification are applied, and the required humidity for the test chamber is provided

The sample rack is designed according to national standards with two layers of O-type and V-type tilted at 15 degrees and 30 degrees respectively, and can also be hooked. The V-shaped bracket is made of PP material, and the O-shaped bracket is made of stainless steel tube wrapped with heat shrinkable PVC film, which has high strength and corrosion resistance.

Bottom: Equipped with 4 advanced universal casters, which can be fixed and adjusted horizontally.

Heating andcontrolSystem:

• The equipment design has two control cabinets: the electrical control system is located on the right side; The gas system, pure water tank, and saturation tank are located on the left side of the box to separate the circuit and water as much as possible, avoiding the risk of water vapor evaporation affecting the life of electrical components and even short circuits.

• High resolution 4.3 inch true color LCD touch screen controller imported from Taiwan, China, China: it can set and display laboratory temperature and saturator temperature, continuous spray or intermittent spray, total test time, etc; Built in automatic tuning function based on PID algorithm; Supports USB storage;

• The heating method for the box is the inner tank sink type, which heats up quickly and distributes temperature and humidity evenly. The temperature fluctuation of the studio after constant temperature is smaller. Adopting U-shaped anti-corrosion titanium alloy high-speed heating electric heating tube

• Temperature sensor: PT100 platinum resistance thermometer

• High quality electrical components: Schneider Electric from France executes components

• The automatic water filling system has the function of automatically replenishing water level when the water level is insufficient: the saturator automatically replenishes water to avoid the tedious operation of frequent manual shutdown and water filling, and the test is not interrupted.

• Equipped with dual over temperature protection and low water level warning to ensure safe use.

• End of experiment instruction

spray fog be Unified:

• Pneumatic spray mode, the air pressure is regulated in two stages: the first stage is the inlet pressure, which is generally regulated at 0.2~0.3MPa; The second level is the spray pressure. In order to meet the requirements of spray pressure in the standard GB/T10125-2012 (precision 2kpa), the spray pressure gauge of this equipment uses a customized high-precision pressure gauge.

• The spray method is to place the embedded glass nozzle in a round plastic pipe, guide the spray through the tower pipe, and then disperse it to the inside of the laboratory through the cone disperser.

• The brine before spray is injected into the spray tower through the brine storage tank.

• The non crystallization nozzle is used for atomization through baffle plate. The fog diffuses evenly and settles freely in the test chamber. The height of the spray tip can be adjusted and guided to the salt fog. The fog particles are small and settle naturally;

• Specially designed quartz glass nozzle, salt free crystallization

• The spray gas passes through the oil-water separator to filter and stabilize the oil-water pressure before entering the saturation cylinder for preheating and humidification, and then passes through the solenoid valve and pressure regulating valve to reach the nozzle

• The saltwater tank is a built-in hidden type with a large storage capacity

• Salt water is filtered through a sand core filter before atomization to prevent debris from clogging the nozzle

• Two standard fog collection funnels are placed in the laboratory and connected to the measuring cylinder outside the box through pipes to monitor the settling amount at any time

Random data and accessories:

• Instruction manual, circuit diagram, certificate of conformity, warranty card;

• Operation methods, precautions, and maintenance matters;

• Basic shipping accessories:

Equipment usage conditions:

• Environmental temperature: 5 ℃ to+28 ℃; Environmental humidity: ≤ 85%; Good ventilation (separate room, well ventilated or equipped with exhaust fan, with sewer for exhaust gas and wastewater discharge within 1 meter distance)

• Gas source requirements: pressure greater than 0.4MPa, rated displacement greater than 0.3m³/Minutes, the device has a quick connector with a diameter of 8mm

• Water source requirements: There is tap water nearby for easy addition and flushing of water inside the equipment, and distilled water or deionized water is also available

• Power requirement: Equipment power cord 3 meters

Y-250C 3kW AC220V/50HZ；

Y-750C 4kW AC220V/50HZ；

Y-010C 5kW AC380 (± 10%) V/50HZ three-phase five wire system;

Y-016C 6.5kW AC380 (± 10%) V/50HZ three-phase five wire system;

Y-020C 7kW AC380 (± 10%) V/50HZ three-phase five wire system;

Delivery instructions:

• The supplier is responsible for the freight and delivery to the doorstep. The goods will be shipped within 30 working days after the prepayment is received;

• The purchaser shall prepay 50% of the total amount, and pay the remaining balance in full after the goods arrive and pass the acceptance inspection;

• The supplier is responsible for introducing installation and debugging operations until the purchaser's employees operate independently;

The warranty period is one year, starting from the date of installation and acceptance. The supplier promises to provide spare parts for life. If after-sales service must be provided on-site, the supplier shall arrive at the user's site within 48 hours.